設計年產150萬噸的中厚板廠_畢業設計說明書-文庫吧

【正文】 ........................................................................................ 25 確定速度圖形式 ................................................................................. 25 選擇各道次咬入、穩定軋制、拋出轉速 ......................................... 26 計算各道次純軋時間 ......................................................................... 27 確定各道次間隙時間 ......................................................................... 28 溫度規程的制定 ............................................................................................ 29 溫度規程的確定 ................................................................................. 29 第六章 力能參數計算 ................................................................................................ 32 確定各道變形抗力 ........................................................................................ 32 各道變形程度的計算 ......................................................................... 32 計算各道平均變形速度 ..................................................................... 33 變形抗力的計算 ................................................................................. 34 軋制壓力的計算 ............................................................................................ 35 計算各道變形區長度 ......................................................................... 35 計算各道平均單位壓力 ..................................................................... 36 計算各道總壓力 ................................................................................. 37 確定各道次傳動力矩 .................................................................................... 38 傳動力矩的組成 ................................................................................. 38 按軋制力計算軋制力矩 ..................................................................... 39 附加摩擦力矩的確定 ......................................................................... 40 內蒙古科技大學畢業設計說明書 空轉力矩的確定 ................................................................................. 43 計算傳動力矩 ..................................................................................... 44 繪制軋制圖表 ................................................................................................ 44 軋輥強度校核 ................................................................................................ 46 粗軋機校核 ........................................................................................ 46 精軋機校核 ......................................................................................... 49 電機能力校核 ................................................................................................ 50 粗軋機電機校核 ................................................................................. 50 精軋機電機校核 ................................................................................. 51 軋鋼機工作圖表 ............................................................................................ 52 第七章 車間的平面布置及主要設備距離 ................................................................ 53 車間的平面布置 ........................................................................................... 53 車間布置原則 ..................................................................................... 53 選擇金屬流程線 ................................................................................. 53 生產設備的布置 ................................................................................. 53 加熱爐、主電室、軋輥間的配置 ................................................................ 54 主要設備間距的確定 .................................................................................... 55 第八章 工作時間及年產量計算 ................................................................................ 57 車間工作制度和工作時 間的確定 ................................................................ 57 軋鋼機產量計算 ............................................................................................ 57 軋機小時產量計算 ............................................................................ 57 軋鋼機平均小時產量 ......................................................................... 58 第九章 主輔設備的選擇及性能參數的確定 ............................................................ 61 加熱爐的選擇 ................................................................................................ 61 推鋼式加熱爐 ..................................................................................... 61 步進式加熱爐 ..................................................................................... 63 高壓水除鱗裝置 ........................................................................................... 64 立輥機架 ....................................................................................................... 65 粗軋機入口推床（粗軋機出口、精軋機入出口） ................................... 65 內蒙古科技大學畢業設計說明書 3800mm 四輥可逆粗軋機 .............................................................................. 65 4100mm 四輥可逆精軋機 .............................................................................. 67 剪切設備的選擇 ........................................................................................... 68 切頭剪 ................................................................................................. 68 雙邊剪 ................................................................................................. 69 定尺剪、火焰切割機 ......................................................................... 69 軋機機架的選擇 ........................................................................................... 70 軋輥壓下裝置的選擇 ................................................................................... 71 軋輥平衡裝置的選擇 ................................................................................. 72 矯直機的選擇 ............................................................................................. 73 冷卻設備的選擇 .......................................................................................... 74 冷床 ..............................................................................................................