管道油漆修補方案(已修改)

　

【正文】 Table of Content 目 錄 一、 Project General Introduction 工程概況 二、 References 編制依據 三、 Preparations 準備工作 四、 Painting Process 涂漆工藝 Confirm the regions that need to repair and repair method 確認油漆損傷部位和修補方法 Surface Preparation Method 表面處理方法 Painting 涂漆 五、 Quality control and Inspection 質量控制及檢查 六、 Safety 安全 七、 Paint Protection 油漆保護 一 二 References 編制依據 三 Preparations 準備工作 The design and other technical document is ready。 the construction drawing is ，施工圖紙業經會審； Construction procedure and technical instructions are pleted。 The safety training and technical training from international pany have been ，進行了安全技術教育和國際公司技術培訓； pipe and fittings shall have qualifications. 管段應具備出廠合格證； Material, tools, apparatus for test and inspection, construction facility and space are ，機具，檢測儀器，施工設施及場地已齊備； Inspection must be done during the course of anticorrosion construction, and perform the acceptance immediately after anticorrosion is ，必須進行中間檢查 ；防腐蝕工程完工后，應立即進行驗收； The coating shall have qualification from its manufacturer 油漆 應有制造廠的質量證明書； Painting environmental condition shall be in accordance with the information on the product sheet. The surface temperature to be dew point relative humidity shall be less than 85%. 涂裝環境條件必須和產品說明書的信息一致。表面溫度至少大于露點30C.。相對濕度最大植為 85%。 Selection of Paint 油漆選用 DC has provided the painting system suitable for this project. The selection of paint shall strictly follow DC construction painting system. Paint type, finish paint color and paint repair color should be chosen in accordance with the line list. The specific painting systems are as follows. 本項目 DC 已經給出了適合本項目的油漆系統，油漆選擇嚴格按照 DC 油漆系統進行選擇施工 。油漆種類、面漆和油漆修補的顏色按照 line list 規定選用，主要有如下種類。詳細油漆系統對照表如下： Painting SystemDC201A 油漆系 統 DC201A DC201A： new steelwork， piping and fabricated equipments， shop prepare（ 20 to 1200C） Location 部位 DC201A Surface reparation 表面處理 Abrasive blast cleaning to ISO85011 , (Roughness 4075 microns)噴砂處理至 ISO85011 ，粗糙度達到 Rz=4075 微米 Coating System 涂層配套 Coat Name 涂層名稱 Product Name 產品名稱 DFT: microns干膜 厚度：微米 Prime Coat 底漆 Inanic zincrich, Interzinc 22 Greenish grey, Matt 無機富鋅底漆 Interzinc 22 綠灰色，平光 6075 MidCoat 中間涂層 MIO Epoxy Intergard475HS Gray 環氧 MIO 中間漆 Intergard 475HS, 灰色 100150 Top Coat 面漆 Polyurethane color： meet Spec’s requirements 聚氨酯面漆 顏色：符合規范要求 6075 Typical Minimum/Maximum DFT Range 典型最小 /最大干膜厚度范圍 220300 Pipe supports sand blasting, painting requirement should be the same as piping,. 管道支架的噴砂、涂漆與管道要求相同。 DC201B： Site work and repairs of steelworks,piping and fabricated equipments (20 to 1200C) Location 部位 DC201B Surface preparation 表面處理 Abrasive blast cleaning to ISO85011 , (Roughness 4075 microns) 噴砂處理至 ISO85011 ，粗糙度達到 Rz=4075 微米 Coating System 涂層配套 Coat Name 涂層名稱 Product Name 產品名稱 DFT: microns 干膜厚度：微米 Prime Coat 底漆 Surface Tolerant Epoxy Intergard670HS 低表面處理環氧漆 Intergard670HS 100150 MidCoat 中間漆 Surface Tolerant Epoxy Intergard670HS 低表面處理環氧漆 Intergard670HS 100150 TopCoat 面漆 Polyurethane color:meet spec”s requirements 聚氨酯面漆 顏色：符合規范要求 5075 Typical Minimum/Maximum DFT Range 典型最小 /最大干膜厚度范圍 250375 DC202A： Galvanized surface,handrais(5 to 600C).(can not use abrasive basting). Location 部位 DC202 Surface preparation 表面處理 清理基層表面油污到 SSPCSP1標準要求。 Coating System 涂層配套 Coat Name 涂層名稱 Product Name 產品名稱 DFT: microns 干膜厚度：微米 Prime Coat 底漆 蝕刻底漆 Interprimer539 1025 MidCoat 中間漆 環氧底漆 Intergard269 3050 TopCoat 面漆 Polyurethane color: meet spec”s requirements 聚氨酯面漆 顏色：符合規范要求 5075 Typical Minimum/Maximum DFT Ran