模具-中英文手冊(留存版)

　　

【正文】 切邊模Unit mold 單元式模具Universal mold 通用模具Unscrewing mold 退扣式模具Yoke type die 軛型模模具廠常用之標準零配件air vent valve 通氣閥第10頁Anchor pin 錨模angular pin 角模angular pin 傾斜模Baffle 調節阻板Baffle plate 折流檔板Ball button 球塞套Ball plunder 定位球塞Ball slides 球塞滑塊Binder plate 壓板Blank holder 防皺壓板Blanking die 落料沖頭Bolster 上下模板Bolster 墊板Bottom board 澆注底板Bottom plate 下固定板Bracket 托架Bumper black 緩沖塊Buster 堵口Casing ladies 澆注包Carting lust 鑄耳Cavity 模穴(模仁)第11頁Cavity retainer plate 模穴托板Center pin 中心梢Clamping block 鎖定塊Coil spring 螺旋彈簧Cold punched nut 冷沖螺母Cooling spiral 螺旋冷卻栓Core 心型Core pin 心型梢Cotter 開口銷Cross 十字接頭Cushion pin 緩沖梢Diaphragm gate 盤形料道Lie approach 模頭料道Lie bed 型底Lie block 塊形模體Lie body 鑄模座Lie bush 合模襯套Lie button 沖模母模Lie clamper 夾模器Lie fastener 模具固定用零件第12頁Die bolder 母模固定板Die lip 模唇Die plate 沖模板Die set 沖壓模座Direst gate 直接澆口Dog chuck 爪牙夾頭Dowel 定位模Dowel hole 導套孔Dowel pin 合模梢Dowel pin 定位梢Dazzle 補助澆口 Draft 拔模錐度Draw bead 張力調整捍Drive bearing 傳動軸承Ejection pad 頂出襯墊Ejector 脫模器Ejector guide pin 頂出導梢Ejector leader blusher 頂出導梢襯套Ejector pad 頂出墊Ejector pin 頂出梢Ejector plate 頂出板第13頁ejector rod 頂出桿ejector sleeve 頂出襯套ejector valve 頂出閥 eye bolt 環首螺栓filling core 椿入蕊film gate 薄膜形澆口finger pin 指形梢 finish machined plate 角形模板 finish machined plate 圓形模板fixed bolster plate 固定側模板flanged pin 帶凸緣銷flash gate 毛邊形澆口flask 上箱floating punch 浮動沖頭gate 澆口gate land 澆口面gibe 凹形拉緊銷goose neck 鵝頸管guide bushing 引導襯套guide pin 導梢guide plate 導板第14頁guide plat 引導柱guide rail 導軌bead punch 頂鐓沖頭headless punch 直柄沖頭heavily tapered solid 整體模蕊盒 hose nipper 管接頭impact damper 緩沖器injection ran 壓射柱塞inlay bushed 嵌入襯套inner plunger 內柱塞inner punch 內沖頭insert 嵌件insert pin 嵌件梢king pin 轉向梢king pin bush 主梢襯套knockout bar 脫模桿land 合模平坦面land area 合模面leader bushed 導梢襯套lifting pin 起模項銷lining 內襯第15頁locating center punch 定位中心沖頭locating pilot pin 定位導梢locating ring 定位環lock block 壓塊locking block 定位塊locking plate 定位板loose bush 活動襯套making die 打印沖子manifold block 歧管檔塊master plate 靠模樣板match plate 分型板mold base 塑料模座mold clamp 鑄模緊固夾mold platen 模用板moving bolster 換模保持裝置moving bolster plate 可動側模板one piece casting 整體鑄件parallel block 平行墊塊parting line 分模線parting lock set 合模定位器pass guide 穴型導板第16頁peened head punch 鑲入式沖頭pilot pin 導銷pin gate 針尖澆口plate 襯板pre extrusion punch 預擠沖頭punch 沖頭pusher 推桿pusher pin 襯套梢rack 機架rapping red 起模桿reentrant mold 凹入模retainer pin 嵌件模retainer plate 托料板return pin 回位梢riding s