海洋石油鉆井常用英語手冊(45頁)-石油化工(編輯修改稿)

　

【文章內容簡介】 排氣 251. What’s the lag time? 遲到時間是多少 252. The well is now stable. 現在井眼已經穩定 BOP and subsea Equipment 防噴器與水下設備 中國最大管理資源中心 253. Cut off the 30” conductor. 割掉 30”隔水管 254. Weld on the 30” bottom flange. 焊接 30”法蘭 255. Hoist and nipple up 30” diverter. 吊裝 30”轉噴器 256. Change the 5” pipe rams to 31/2” rams. 把這個 5”閘板換成 31/2” 257. Install blind ram. 安裝防噴器的盲板芯子 258. Check the seal ring of the conductor. 檢查隔水管密封圈 259. Cut off the lifting eye of the conductor. 切割隔水管耳環 260. Test BOP. 測試防噴器 261. Change annular BOP packing. 更換萬能防噴器芯子 262. Full pressure test the ram preventers. 對閘板防噴器進行全壓試壓 263. Test annular BOP at 2500psi. 萬能防噴器試壓至 2500psi 264. Check annular pressure. 檢查環形空間壓力 265. Confirm the angle of the guide base. 確定基板角度 266. The thread is covered with the quickrelease protectors. 已戴好快卸護絲 267. Establish the guide lines. 裝導向繩 268. Connect the TGB running tool. 接臨時導向基板送入工具 269. Land the TGB to sea. 下臨時導向基板到海底 270. Retrieve the running tool. 退出送入工具 freestore 20200801 13:49 1. Run the BOP and risers. 下防噴器和隔水管 2. Pick up the marine riser. 吊出隔水管 3. Pick up the slip joint. 起伸縮節 4. Adjust the riser tensioners. 調整隔水管張力 5. Function test the diverter system. 對防噴器系統進行功能測試 6. Retrieve the pin connector. 取出銷釘連接器 7. Move the BOP to the moonpool door. 將防噴器移到園井甲板的活動門上 8. Run the test plug. 下試壓塞 9. Close the upper pipe ram. 關上部鉆桿閘板防噴器 10. Open the kill line valve. 開壓井管線閥 11. The pensation capacity is 400000 pounds. 補償能力是 400千磅 12. The locking load is 1000000 pounds. 鎖緊負荷 1000千磅 13. Support the riser. 接隔水管支撐環 14. Remove the hose bundles. 卸下垮接軟管 15. Assure the selfcontrolled rotation. 保證自控轉動 16. Set the LMRP on the test pump. 將下部防噴器插入總成座放到試壓樁上 17. Connect the flex joint to the riser. 連接隔水管與撓性接頭 18. Land the BOP onto the well head. 座防噴器到井口頭 19. Run the subsea TV for monitoring. 下水下電視觀察 20. Remove all the riser running tools. 取出所有的隔水管送入工具 中國最大管理資源中心 21. BOP carrier. 防噴器叉車 22. Lower the universal guide frame. 下放萬能導向架 23. Paint mark the top 6 meters of 30” conductor white. 在 30”隔水管的頂部 6米處用白漆涂上記號 24. Check adequate length for guidelines. 檢查導向繩的長度是否足夠 25. Move temporary guide base (TGB) into moonpool. 將臨時導向基板到園井甲板 26. Test pull to check connection. 試拉檢查連接 27. Grease TGB and running tool as required. 按要求給導向基板及下入工具上黃油 28. Test fit TGB and running tool. 用下入工具試臨時導向基板連接 29. Check for junk inside shoe joint. 檢查浮鞋內有無落物 30. Pick up 30” conductor handling slings and shackles. 吊上下 30”導管的索具和卸扣 31. Is slope indicator properly mounted? 水平儀是否裝好 ? 32. Ensure subsea TV is in good condition. 確保水下電視處于良好的狀態 33. Place BOP stack on the test pump. 將防噴器組放在試壓樁上 34. Check condition of all 30” casing connectors. 檢查所有 30”套管接頭的情況 35. Replace Orings as required. 按需要 , 更換 O性密封圈 36. Attach slope indicator below camera position. 在攝像機下面裝上水平儀 37. Inspect and repair diverter. 檢查并修理轉噴器 38. Prepare spud plate and wireline to check water depth. 準備測深板和鋼絲繩測量水深 39. Record all pressure tests on a chart recorder. 用試壓表記錄試壓記錄 40. Visually inspect all sealing element. 目視檢查所有密封件 41. Check and tighten all bolts. 檢查并上緊所有螺栓 42. Bleed off surface accumulators. 地面管線排空氣 43. Check for leaks. 檢查有無泄漏 44. Lift BOP stack and replace wellhead connector AX ring. 吊起防噴器組并更換連接器 AX密封圈 45. Function test wellhead. 對井口頭進行功能試驗 46. Fill kill and choke valves with seawater. 將壓井閥和阻流閥注滿海水 47. Pressure test to 500psi then bleed off test pressure. 試壓到 500psi, 然后放掉壓力 48. Reduce hydraulic control manifold pressure to 5200 kpa. 將液壓控制管線壓力減少到 5200千帕 49. Switch to alternate control pod. 把閘門開關倒到控制面板 50. Guidelines are slacked off. 導向繩松了 51. Slack off drill pipe and release running tool. 放松鉆桿并卸開下入工具 52. Run subsea TV to observe bit entering the TGB. 下水電視觀察鉆頭是否進入臨時導向基板 53. Don’t rotate until hole opener passes through the TGB. 在擴眼器通過臨時 中國最大管理資源中心 導向基板前不要旋轉 54. Position permanent guide base (PGB) below rotary table. 在轉盤下安放永久導向 基板 55. Monitor riser level via trip tank. 用計量罐來控制隔水管內的液面 56. Pressure test to 5000psi. 試壓 5000psi 57. Pick up test mandril and place in BOP. 吊起試壓防噴器芯子并裝入防噴器組 Safety and Firefighting 安全與消防 328. Get a Work Permit before you can start the hot work. 辦理作業許可證才能進行動火作業 329. Welding is not allowed. 不準動焊 330. Put on your (safety) helmet. 戴上安全帽 331. It’s a high voltage area. 這是高壓區 332. That’s against the rule. 這是違章作業 333. Don’t walk under the crane load. 不要在吊物下走動 334. The repairing is under way. 正在檢修 335. Keep your hands clear! (Keep you hands off! Do not touch!) 不要亂動 336. Wear and secure your safety belt. 戴上并系好安全帶 337. Life jacket must be worn when working outboard or overhead. 舷外或高空作業要穿救生衣 338. Have your breathing apparatus near you. 保持放毒面具在附近 339. It’s a drill. 這是演習 340. It was a BOP drill. 這是防噴演習 341. Get in the lifeboat in order. 按順序進入救生艇 342. Put on life jacket! 穿好救生衣 343. Abandon the vessel! 棄船 344. Sound the abandonment alarm! 發出棄船警報 345. Go to the helideck! 去飛機坪集合 346. Aboard the lifeboat. 登上救生艇 347. Aboard the supply boat to shore! 乘拖船上岸 348. Check life saving apparatus periodically. 定期檢查救生設備 349. It’s for fire fighting. 這是消防用的 350. Start the fire pump. 啟動消防泵 351. This rope is too small. 這根繩子太細了 352. It should be function tested. 需做功能測試 353. A warning notice should be set up. 要掛警告牌 中國最大管理資源中心 354. Do you have an emergency program (contingency plan)? 你們有沒有應急計劃 ? 355. It must be ready in an emergency condition. 必須始終保持良好的應急狀態 356. Will the typhoon hit our rig? 臺風要襲擊我們的平臺嗎 ? 357. We will have to evacuate the rig. 我們要撤離平臺 358. Personnel on board (POB). 在船人員總數 359. Sound fire alarm. 發消防警報 360. This is a fire drill. 這是消防演習 361. condu