was集群部署方案及安裝配置手冊(編輯修改稿)

　

【文章內容簡介】 l keystore ClientDefaultTrustStore with the following SHA digest: A9:BA:A4:B5:BC:26:2F:5D:2A:80:93:CA:BA:F4:31:05:F2:54:14:17ADMU0001I: Begin federation of node AAAAAPP2******Node01 with Deployment Manager at **.**.**.36:8879.ADMU0009I: Successfully connected to Deployment Manager Server: **.**.**.36:8879ADMU0505I: Servers found in configuration:ADMU0506I: Server name: server1ADMU2010I: Stopping all server processes for node AAAAAPP2******Node01ADMU0512I: Server server1 cannot be reached. It appears to be stopped.ADMU0024I: Deleting the old backup directory.ADMU0015I: Backing up the original cell repository.ADMU0012I: Creating Node Agent configuration for node: AAAAAPP2******Node01ADMU0014I: Adding node AAAAAPP2******Node01 configuration to cell: APP1Cell01ADMU0016I: Synchronizing configuration between node and cell.ADMU0018I: Launching Node Agent process for node: AAAAAPP2******Node01ADMU0020I: Reading configuration for Node Agent process: nodeagentADMU0022I: Node Agent launched. Waiting for initialization status.ADMU0030I: Node Agent initialization pleted successfully. Process id is: 6848ADMU0300I: The node AAAAAPP2******Node01 was successfully added to the APP1Cell01 cell.ADMU0306I: Note:ADMU0302I: Any celllevel documents from the standalone APP1Cell01 configuration have not been migrated to the new cell.ADMU0307I: You might want to:ADMU0303I: Update the configuration on the APP1Cell01 Deployment Manager with values from the old celllevel documents.ADMU0306I: Note:ADMU0304I: Because includeapps was not specified, applications installed on the standalone node were not installed on the new cell.ADMU0307I: You might want to:ADMU0305I: Install applications onto the APP1Cell01 cell using wsadmin $AdminApp or the Administrative Console.ADMU0003I: Node AAAAAPP2******Node01 has been successfully federated.此時再到app1主機的DMGR控制臺可以看到節點app2主機的SERVR1可以啟動app2機上的SERVER1。(至app2機上的profiles/appsvr01/bin下執行./ server1也可)六、 兩應用服務器建集群。把app1與app2的應用服務放在集群中刪除兩個應服務器下的單個SERVER。停止兩個服務后，刪除，保存設置把單個服務器刪除建集群，起名HR_cluster注意：把配置HTTP會話內存到內存的復制勾上。“下一步”，分別對應兩應用服務主機，各一個SERVER，分別名稱為app1app2集群建完后如下到系統管理－＞節點　中同步各節點啟動集群集群可正常啟動至此，兩臺應用服務器的集群安裝完畢！七、 安裝WEB服務器33機安裝HTTP　SERVER與PLUGINS插件程序安裝包在/_install目錄下，解壓解包后，執行_ins/ihs/，用xmanager來執行該文件進行安裝。安裝畫面如下：第一步設置端口，選擇默認的Web1機的 port 80 administration port 8008后面一步，在設置插件安裝目錄與應用服務器主機名稱那里，33對應的插件安裝目錄是默認的/opt/IBM/HTTPServer/plugins對應的應用服務主機名設為 app1(注意：34那臺機安裝erver時，選擇對應的應用服務主機設為app2，其他過程都相同)注意在管理用戶與口令那里設置為admin,******注意：因為這兩個web服務器要通過另外一臺應用服務器的dmgr來管理，所以這里的安全管理用戶與口令要設。否則dmgr上無法管理啟停。下面這一步，設置用戶與組分別為nobody,nobody (注意：這個用戶與組在etc/group,passwd,shadow中要有)33上WEB服務器安裝完成34上HTTPSERVER完裝過程類似，只是先把對應的應用服務器主機名設為app2八、 兩臺WEB服務器的啟動過程正常過程：在兩臺WEB服務器下，HTTPServer/bin目錄下，執行如下腳本，啟停apache服務./apachectl start./adminctl start提示./adminctl start: admin started 九、 回到app1的DMGR主控制臺，建立WEB服務節點與啟動管理。選擇系統管理－＞節點，增加非受管制的兩個WEB節點(前面兩個app節點是受管制節點)點添加，選擇非受管節點為WEB1機上的節點命名并設置主機名稱非受管節點名稱：webnode1主機名：web1第一個節點添加成功再同樣操作繼續添加第二個非受管節點非受管節點名稱：webnode2主機名：web2然后回到服務器類型下，選擇WEB服務器，選擇兩個非受管節點，分別去創建webserver1下一步后，增加設置屬性，管理用戶與口令 .用戶與口令是在WEB機上安裝HTTP　SERVER時的設置admin,admin完成第