中英文模具詞匯word版-資料下載頁

　　

【正文】 ushes 導板 guide plate 滑板 sleek plate 耐磨板 wear plate 彈壓導板 spring guide plate 鋼球保持圈 cage 止動件 retainer 固定零件 retaining elements 上模座 punch holder (upper shoe) 下模座 die holder (low shoe) 凸模固定板 punch plate 凹模固定板 matrix plate 墊板 backing plate 模柄 shank 浮動模柄 selfcentering shank 其他零件 斜楔 cam driver 滑塊 sleek block3 沖模設計術語 沖裁間隙 blanking clearance 模具閉合高度 die shut height 壓力機閉合高度 shut height of press machine 沖模壽命 die life 壓力中心 center lf load 沖模中心 center of die 沖壓方向 pressing direction 送料方向 feed direction 排樣 blank layout 搭邊 scrap 進距 feed pitch 切邊余量 trimming allowance 毛刺 burr 沖裁力 blanking force 彎曲力 bending force 拉伸力 drawing force 擠壓力 extruding force 卸料力 stripping force 推件力 ejecting force 頂件力 kicking force 壓料力 pressureplateforce 壓邊力 blank holder force 毛坯 blank 中性層 neutral plane 彎曲角 bending angle 彎曲線 bending line 回彈 spring back 相對彎曲半徑 relative bending radius 彎曲半徑 bending radius 最小彎曲半徑 minimum bending radius 彎曲件展開長度 blank length of bends 拉伸系數 drawing coefficient 拉伸比 drawing ratio 拉伸次數 drawing numbers 擠壓比 extruding ratio 縮口系數 necking coefficient 擴口系數 flaring coefficient 脹形系數 bulging coefficient 翻孔系數 burring coefficient 最小沖孔直徑 minimum diameter of piercing 轉角半徑 radius 相對轉角半徑 relative radius 相對高度 relative height 相對厚度 relative thickness4 圓凸模結構要素 頭部 punch head 桿 shank 刃口 point 頭厚 punch head thickness 頭部直徑 punch head diameter 連接半徑 radius 凸模圓角半徑 punch radius 桿直徑 shank diameter 引導直徑 lead diameter 過渡半徑 radius blend 刃口直徑 point diameter 刃口長度 point length 凸模總長 punch overall length5 圓凹模結構要素 頭部 matrix head 模體 body 刃口 point 刃口直徑 hole diameter 刃口長度 land length 刃口斜度 point angle 凹模外徑 body diameter 頭部直徑 matrix head diameter 頭厚 matrix head thickness 凹模圓角半徑。matrix fillet radius 凹模總長 matrix overall length 引導直徑 lead diameter 排料孔 relief hole 排料孔直徑 relief hole diameter 連接圓角 fillet 壓料板，壓邊圈 blank holder 進料速度 approaching speed 滑塊上升速度 slide upstroke speed 沖程 stroke 支柱，支桿 uprights 滾珠傳送帶 roll conveyor 卷邊模 crimping dies 開料尺寸 strip widthAssembly line 組裝線Layout 布置圖Conveyer 流水線物料板Rivet table 拉釘機Rivet gun 拉釘槍Screw driver 起子Pneumatic screw driver 氣動起子worktable 工作桌OOBA 開箱檢查fit together 組裝在一起fasten 鎖緊(螺絲)fixture 夾具(治具)pallet 棧板barcode 條碼barcode scanner 條碼掃描器fuse together 熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME 制造工程師MT 制造生技cosmetic inspect 外觀檢查inner parts inspect 內部檢查thumb screw 大頭螺絲lbs. inch 鎊、英寸EMI gasket 導電條front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 電源按鍵reset button 重置鍵Hipot test of SPS 高源高壓測試Voltage switch of SPS 電源電壓接拉鍵sheet metal parts 沖件plastic parts 塑膠件SOP 制造作業程序material check list 物料檢查表work cell 工作間trolley 臺車carton 紙箱subline 支線left fork 叉車personnel resource department 人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory沖壓廠painting factory烤漆廠molding factory成型廠mon equipment常用設備uncoiler and straightener整平機punching machine 沖床robot機械手hydraulic machine油壓機lathe車床planer |plein|刨床miller銑床grinder磨床linear cutting線切割electrical sparkle電火花welder電焊機staker=reviting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager | =vice manager副理section supervisor課長deputy section supervisor =vice section superisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕臺Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |39。skr?pid|報廢scrape ..。削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良o(jì)xidation |39。 ksi39。dei?n|氧化scratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良embedded lump鑲塊feeding is not in place送料不到位stampingmissing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts=buffer備件forklift叉車trailer=long vehicle拖板車pound die合模die locker鎖模器pressure plate=plate pinch壓板bolt螺栓administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzle蜂鳴器defective product label不良標簽identifying sheet list標示單location地點present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位prefixed finishing date預定完成日approved by / checked by / prepared by核準/審核/承辦PCE assembly production schedule sheet PCE組裝廠生產排配表model機鍾work order工令revision版次remark備注production control confirmation生產確認checked by初審approved by核準department部門stock age analysis sheet 庫存貨齡分析表onhand inventory現有庫存available material良品可使用obsolete material良品已呆滯to be inspected or reworked 待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by制表 notes說明yearend physical inventory difference analysis sheet 年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semifinished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/nongood parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head掛鉤槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torchflame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓沖子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線沖子aircushion ejectrod氣墊頂桿springbox ejectplate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor系數phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁。消磁highspeed transmission高速傳遞heat dissipation熱傳 rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished pr